- Shipping Company Estimated Delivery Time Shipping Cost
Highlights
Configurable
The SP Racing F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
Flight Logging
On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.
Developer Friendly
Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
Broad RC receiver Support
Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers.
(No external inverters required (built-in).)
Battery Monitoring
Battery monitoring ports for voltage and current.
I2C Port
I2C port always powered, perfect for external sensors or always-on OLED Screen.
No-Compromise I/O
Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!
Tiny and lightweight
The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.
Next-Generation CPU
The SPRacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time.
Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
OneShot ESC
Full support for OneShot ESCs for easy PID tuning and a sharper response.
Programmable LED
Dedicated output for programmable LEDs - great for orientation, racing and night flying.
Other Features
Sonar: Sonar support for precision low-altitude hold.
Buzzer port for audible warnings and notifications.
The SP Racing F3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography. it's perfect.
Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.
Flight Performance
The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.
3 primary flight modes
Acrobatic, Angle and Horizon
Extensive control and switch configuration
Telemetry Support (HoTT, FrSky, SmartPort, etc)
Battery Monitoring and Warnings
Signal Strength Monitoring (RSSI)
Failsafe system
Altitude Hold Mode (Requires Barometer Sensor)
Heading Hold Mode (Requires Compass Sensor)
In-flight tuning
Customizable LED colors
Android phone support (via EZ-GUI GCS)
Next-generation hardware for your multi-rotor
The Seriously Pro Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled and I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU.
MS5611 barometer (Deluxe only)
- HMC5883 compass (Deluxe only)
Specification
| General | |
|---|---|
| Type | Flight Controller Board |
| Model | Deluxe(with barometer & compass) |
| CPU | STM32F303 CPU, 72Mhz inc FPU |
| Panel | 36x36mm plate, 30.5 mm mounting holes |
| Cable length | Approx.110mm |
| Compatible | FPV Quadcopter |
| MicroUSB socket | 2 x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND) 8 x 3pin though-holes for pin headers for ESC/Servo connections 2 x 4pin though-holes for pin headers for 2x serial ports 1 x 2pin though-holes for pin headers for battery voltage 1 x 2pin though-holes for pin headers for buzzer 1 x 4pin JST-SH socket for I2C 1 x 4pin JST-SH socket for SWD debugging |
| Package Contents | |
| 1 x SP Racing F3 Deluxe Flight Controller(with some accesseries) | |
